• 18-gauge brad nailer and 1-gallon compressor combo kit

• Nailer: adjustable depth of drive, rear exhaust, easy-open latch, no-mar pad, low-load-indicator

• Compressor: 1 gallon; aluminum cylinder with steel sleeve; 20-pounds

• Includes nailer, 1/4-inch -by-25-foot hose, safety glasses, fittings, oil, 1,200 brad nails, wrenches, and manuals

• 1-year warranty on nailer; 90-day warranty on compressor

THE BRAD NAILER:
The gun is lightweight and small enough to get into tight spots, yet it appears to be very well built. The protective no-mar pad does not scratch prefinished moulding, and the side load magazine is convenient and easy to use. I shot about 200 2" brads while installing new 1/2" baseboards and 3/4" birch door trim in my bedroom. Every brad was countersunk to perfect depth, and I did not get a single jam. I ended up with very professional results and finished in 1/2 the time it would have taken me with the old hammer and finish nails.

THE COMPRESSOR:
The PC1010 will change the industry. For homeowners, hobby woodworkers, and customer service professionals in the cabinetry industry this is the perfect compressor. There is no need to lug around a 4 or 6 gallon compressor for a little brad nailer. You can easily carry the nailer, hose, and bread box sized compressor in one hand. From startup, this quiet, lightweight little workhorse takes about 2 minutes to pump up to 110 psi. I consistently got 10 shots before kick in, then another 40 seconds or so to recover. I nailed right through the recovery time, and never had to wait for the compressor to before driving any brads.

SHORTFALLS:
It is very difficult for me to find anything that I don't like about this one. However, rumor has it that Senco guns work best with Senco brads, and the local home improvement stores sell mostly PC and Bostich... so I will need to find another source. I would not recommend the PC1010 for anyone who wants to drive anything larger than 18ga brads, or run multiple air tools from a single compressor. Also - the compressor is so new that Senco has very limited literature on it, but I would be willing to bet they will get this taken care of soon.

CUSTOMER SERVICE:
Some of the best customer service I have had the pleasure to work with. If you purchased from an authorized dealer, and you have any problems with your equipment, I recommend calling Senco directly.

21 of 21 found the following review helpful:


compressor try's hard but comes up a bit short  Feb 03, 2004 By Jonathan Hale "professional cabinet and furniture maker"
I agree with the other reviewers who have given praise to this product. I felt the same way till mine broke after less than a months use.
Of course it was the compressor which broke, the part with the 90 day warranty. I did not catch that when I bought this.
Senco is a good company, but I think this little compressor is not quite up to the quality of their other products.
In my case it was the 1/4" copper tubing which brings the air to the tank that failed. It split where the tubing had been bent.
I have fixed it with some liquid steel, since I'm on a job with it, I'm hoping the repair lasts till I have time to replace to tubing.
I have used this to build two large bookcase and cabinet projects so far, and in doing so I have learned the compressors limitations. It does not do well
shooting two inch nails into MDF. It does not have the power to fully sink the nail into the material. I bought this combo for the light weight
of the compressor, so I guess there must be some compromises. This won't take the place of more powerful compressors,
but it is great for carrying to and from a job. I just hope I do not have problems with it in the future. I'm not sure I would
recommend this product, the 90 day warranty on the compressor is a big negative. especially since it seems to have some problems.

20 of 20 found the following review helpful:


Woodworker Hobby or Trim Tool  Jun 23, 2004 By F Baker
I got this package for very light duty use - woodworking shop projects and qtr-round molding on flooring. The nailer is a quality tool that sells for $120 everywhere so that makes the compressor only $75. I had a $15 coupon so the compressor was only $60 for me.
The compressor is so light that it is no problem carrying it. The tank pressure is 125 lbs and I set the tank outlet pressure to 90 lbs. It shoots about 10 brads before it cycles but you can keep shooting as it runs. I used 5/8" brads on molding on a shop project and 2" brads on floor qtr-round without a single problem. This sure saves time and doesn't mar the wood. It is pretty quiet and also looks good. Getting to small jobs and using this little tool is a pleasure. I will get an air blower tip for it; so far I'm satisfied.

21 of 22 found the following review helpful:


I'm impressed.  Aug 10, 2003 By A. Conneen "St.PeteWoodworker"
I upgraded to this from a cheap little electric brad nailer that could not sink a 1" brad. This tool is light and has plenty of power. The compressor is small & quiet and has absolutely no problem keeping up with the nailer. I own an old 5 horse 220 v compressor but wanted something to use inside the house without running hundreds of feet of hose from the garage. This will fill my needs perfectly.
P.S. I shop online alot and would like to say that Amazon.com has the best customer service of any company I have dealt with.

See all 37 customer reviews on Amazon.com